• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Most homeowners can fix hinges that are loose. However, if the screw holes are damaged and can't hold screws, you might have to use dowels and wood glue before you can reinstall the hinge.

Before you do that though scrub away any the surface rust. This will aid in keeping the dowels in place and provide an adequate base to hold onto.

Eliminating the Hinges

Many standard door hinges are removable, which makes it easier to move the door from one side to another or to take the entire door off of the frame, if needed. Removing the hinges for upvc doors is fairly simple for anyone with patience, but you need to know how to do it correctly.

If the hinges have been painted, you will need to remove the paint prior to attempting to remove the pins. You may scratch your door if you do not remove the paint. To break the seal of the paint, place the hinges in an stainless steel pan and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for about 30 minutes. The heat of the water will soften the paint, making it easier to remove.

After the pins have been loosen then you can remove the hinges from the frame and door. It is possible to use a regular screwdriver, but it is recommended to use a magnetic screwdriver for this project. This type of screwdriver was designed to remove screws made of metal and make the task go much faster.

Before you attempt to remove the hinges it is recommended to spray them with a oil. A simple lubricant can help the process to go more quickly and make it easier to remove the screws and pins. You can find this kind of lubricant at a variety of hardware and home improvement stores.

Keep in mind that the number of hinges you'll require will vary depending on the door's type and its settings. Heavier doors and solid-core aluminium hinged doors will need more hinges, while hollow-core doors that weigh less may only require two or three hinges.

It is also essential to understand the different types of window hinges repair to determine which ones will best suit your needs. Exterior hinges are typically designed to support the weight of the door, while interior hinges will have to be able to handle heavier loads.

Reattaching the Hinges

Sometimes, the hinges on doors loosen over time and start to hang crookedly or slide. This can be a problem, but it's usually easy to fix. In most cases it's a simple tightening of the screw will resolve the problem. If the screw holes have been stripped out, it may be a challenge to complete. A dowel made of wood can be used to tighten the holes again.

Start by drilling the hole using a drill close to the size of the new screw (normally 3/8"). Fill in the hole with wood glue and a wooden stick. To ensure a snug fit, the dowel should be cut at the same length as the screw. Then, reinstall the screw and tighten it until the desired degree of tightness. If the door continues to bind up, add another dowel to the gap. Repeat the procedure. Be sure to shut the door slowly so that you can check the perimeter clearances after each adjustment.

Another option is to just use an old-fashioned wood plug instead of dowel. This will work as well however it may take some time to set up. Simply whittle a chunk of wood that is the right size for a snug fit, then press it into the hole. If you don't have a wooden tool, you can also make use of toothpicks or wooden matches as well.

Use a countersink to make the hole smaller for the head of screw after you have reinstalled it. This will prevent the screw from hitting the edges of the doors when they are closed and opened. This will make it easier to tighten the screws after installing hinges.

Once you have reinstalled the hinge, make sure to lubricate it with a dry lubricant in order to help keep it from getting stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. Apply a thin coat and wait for around 15 minutes to fully get into the barrel of the hinge.

Refinishing the Hinges

If you're not yet ready to replace your hinges, you can try a few simple fixes. Verify that the screws that secure the hinge plate to both the bi-fold door hinges frame and the frame are tight. If they're loose, tighten the screws with a power drill or screwdriver. Be careful not to over tighten the screws as this can create gaps at the trim joints or worse, strip the threads.

If the issue is that the hinge plates are separated from the jamb and door and jamb, you can fix the hinges by applying wood glue to the back of the plates and then inserting toothpicks or wooden dowels into the holes. Dowels or toothpicks will provide a solid base for the screws and keep the plates from moving when you drive them into place. Let the glue dry before reattaching the hinge.

Another common cause of loose hinges is that screws are worn out or gone. This can be corrected by replacing the screws. Use a drill bit that is the same size as the screw hole to avoid drilling into the jamb or hinge.

Close the door once you have reattached your hinge and check the gap between the frame and the door. It should be approximately the thickness of a nickel all the way around, or less if there's an existing gap caused by a previous door that hung improperly. If the hinges were put in place properly, this shouldn't be a problem.

If you find that the hinges (click here to read) remain loose, try putting the thicker shim of the hinge between the hinge plate and the mounting surface to give an extra inch of space. You can also try removing the hinge pin from the problem hinge and pounding it down with a hammer in order to make it tighter or use the hinge pin from a different angle altogether. You can also lubricate the hinges using mineral or jojoba oil to decrease friction and help them hold their position. Periodically lubricating your hinges can aid in keeping them from becoming stiff or squeaky, and will also prolong their lifespan.

Cleaning the Hinges

The continuous movement of hinges causes friction, which attracts dust particles. These particles can get stuck and accumulate in the moving parts of door hinges if they are not maintained and cleaned regularly. The hinge will get stiff and creaky, and its appearance may rapidly deteriorate. Regular cleaning, lubrication, and inspection can help preserve the quality of a door's hinges and ensure their proper operation.

Inspect the hinges to see how much rust has accumulated on their surface. If the corrosion has reached the point of destroying surface of the hinge barrel or screw holes, you'll need to replace the hinges. If you are able to save the hinges, begin by brushing away loose rust using steel wool and wire brushes. Then, apply an industrial rust remover or homemade solution like lemon juice on the hinge. Let the rust-removing solution remain on the repair window hinges for several minutes in order to penetrate and dissolve the remaining rust.

If you do not want to spend money and time replacing your hinges, simply retightening the screws can restore the hinges' functionality. If you've sanded the screws, however, it may be necessary to attach a wooden dowel or shim to the hinge. Dowels made of wood are round pieces made of wood in the shape of rods that are available in various lengths and sizes. You can find them at home improvement centers, woodworking supply and craft shops, or online.

A shim may be made of a piece of metal or plastic, depending on the type of hinge you have. To make a dowel, you need to cut a wooden dowel to the desired length. You can dip the dowel into carpenter's adhesive and insert it in the hole. The glue will hold the dowel securely in the position.

Before you begin cleaning the hinges, lay down a paper or cloth towel to protect flooring and other surfaces from drips and spills that could happen. After the area has been secured, proceed to clean the hinges using a soft sponge or cloth that has been soaked in mild cleaner or vinegar to remove dirt, grime, and tarnish. A small brush or toothbrush can be used to reach difficult-to-reach places in crevices and difficult spots.