• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat ducato key fob 500 Key Fob Won't Work

A key fob for Fiat Replacement Car Keys 500 makes it easy to open doors and start your car. There are a myriad of reasons the key fob might stop working. This could be due to a dead battery and water damage, as well as receiver modules issues, and interference.

This listing is for a NEW replacement key for fiat ducato van fiat doblo van remote key Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). Includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob doesn't function is due to a dead battery. Modern key fobs come with a limited operating range and must be within only a few feet from the vehicle to operate. If you're far from your vehicle and you press the key fob button the car won't be able to respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the coin cell battery (Part number CR2032) with a new one from a reputable manufacturer like Panasonic, Duracell, or Energizer. They are usually available at your local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your replacement fiat 500 keys derby 500. The car will flash its parking lights and the key fob should work the lock and unlock switches.

If your key fob still isn't working after replacing the battery, there may be water damage that prevents it from communicating with the module inside your vehicle. Water damage can occur in many ways, such as a simple splash or submerging the key fob saltwater at the beach. If you suspect your fob has been exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If this doesn't work, you will require your fob to be replaced by an auto locksmith or dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob in the ocean, or wash it in a machine. Saltwater is especially dangerous to the circuit board of the fob, causing it to short out and eventually end up dying. It's not a good thing to get the fob wet but don't give up in the event that you accidentally drop it in water, or fail to remove it from your pocket.

First take the battery off the fob. Before replacing the battery, clean the electronic chip with isopropyl or another similar product. Test the fob next to determine if it's working. If the key doesn't function, it may need to be programmed again. This is usually handled by an auto locksmith or dealer.

If your key is old and is not programmed to work with your vehicle, you will need to replace it completely. A professional locksmith for cars will be able to complete this process. The locksmith will require the key cut to match the car's ignition. The locksmith will also need to program your fob into the car's system. This is a cost-effective and quick procedure that can be completed the same day.

Receiver Module Issues

The 500 key fob you have may not function because it's out of range. The remote usually has an area of 30 feet or less and if it's far away from your car it will not respond to your commands. You can easily solve this issue by moving the remote closer to your car until it responds.

If your fob won't work after you replace the battery for the coin, also called a "button", "watch" or "button" It could be a problem with the circuit board inside. In most cases, reprogramming the fob will resolve this problem. You can find instructions on how to do this for all vehicles by searching YouTube or checking out the owner's manual.

You may have to replace the metal retaining clips that keep the battery of your coin in place. If they lose tension it could hinder the coin battery from sitting properly, and this will cause your remote to malfunction.

In rare cases it is possible that the fob will become disconnected from your vehicle due to software issues or hardware issues. This could be a huge issue, but you are able to usually fix it by visiting a local dealer or auto locksmith to reprogram your fob for you. In some instances it may be necessary to reinstall the program in your body control module, too.

Interference

Interference can also cause the key fob to not be able to receive or transmit signals. This can occur when the keyfob's location is in close proximity to a radio transmitter, like a cellphone or radar detector. The key fob might not function because of a problem to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you've tried everything at home to resolve it (e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module is situated under the dash, and it picks up the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets.

There is a simple way to reset the 500's onboard system including the keyfob. Disconnect the 12 volt battery for about 15 minutes, by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will get rid of any remaining electricity and then restart the car's computers, which could allow you to the key fob to function again. If the issue persists, you should consult an expert technician. They will be able to determine the root of your issues.