• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, patio door wear and tear could cause lock malfunctions. Fortunately, there are several simple and efficient steps that can help restore your uPVC patio door's security.

It's about realigning the lock or cleaning the locking mechanism these simple fixes will make your home more secure.

Clean the Lock

Although patio doors are a great way to let the outside in and keep the elements out but they can also pose security risks if your lock isn't working as it should. Over time, wear and tear, cold and hot weather, dirt, and debris can cause your patio door lock to become difficult to operate. With a little attention you can ensure that your patio door's lock always works properly.

It is important to first clean the patio door lock and all moving parts. This helps to remove any dirt and coatings that could be preventing the lock from working in the way it should. Start by wiping all the moving parts on your patio door lock with an aqueous cloth. Then, use a scouring cloth or a damp, rough cloth to scrub the areas that are soiled of the frame and door. Then wipe the lock using a dry towel to get rid of any remaining moisture. Let it air dry before using it.

If you have a patio door that uses a pin tumbler latch mechanism, you can lubricate the lock by applying powdered graphite to the key or by using a Teflon-based lubricant like WD-40 Multi-Use. This type of lubricant can be easy to apply and doesn't break down over time. If you are unable to find the right lubricant for your lock, apply a pencil that has a larger tip. Put the pencil into the lock and move it around a bit to distribute the graphite.

Tracks for sliding patio doors require regular maintenance to keep them free of dust, dirt and other debris. They are particularly susceptible to snow, ice and other debris that could cause them to get stuck or to bind. This could make it difficult for your patio door to open and shut.

The sliding rails of the patio door track and rollers can be cleaned by removing any dirty or damaged weather stripping and then cleaning it, before replacing it. The same can be done to patio sliding door repair door rollers which can be cleaned and sprayed with non-stick lubricant to help them move freely.

Lubricate the Moving Parts

uPVC french doors, like sliding patio doors, operate using 3 to 4 or sometimes 5-point locking mechanisms which include the handle and lock cylinder controlled by a key. They also require maintenance, and specifically lubrication of the moving parts. This can be done with an oil that is thin but not WD40. It is recommended to do it at least once a year.

If hinges that are sagging don't cause the problem it could be because the door is misaligned. It may be rubbing against or catching the strike plate's opening in the frame. Remove the strike plate and employ a sharp tool enlarge its mortise. This will allow the latch to fit into the hole, and also prevent it from hitting the frame.

When the cylinder is out of the way, measure its width with the help of a book or piece wood that fits into the gap between the adjustment screw and the lock. The outer dimension is the distance from the outside of the door to the middle of the cylinder, and the inner dimension extends from the center of the adjustment screw to the end of the cylinder.

Verify the lock's width

If your patio door latch is hard to turn, even after cleaning and oiling it could be because it's not aligned with the strike plate. Check to see if the door is in balance and if the hinge screws are tight, but in many cases it is possible to move the strike plate up or down can fix the issue.

Most of the time, the issue occurs when the lock's strike is too small for the latch to engage. In this instance you'll have to increase the hole with either a hammer or chisel, and then test the latch to ensure that it connects to the strike plate without rubbing against or landing on the door's frame jamb.

You must identify the kind of mortise lock you have before purchasing an alternative. This can be done by looking at the end faceplate and observing whether it is square or round. Then, take a look at the screw holes on the current lock and note the size of each. This will help you find a replacement that is the same width and is a perfect fit for the hole that you already have.

You'll need to locate the mortise lock, and then examine it for any scratches, bends or other damage that requires to be repaired. A damaged or bent latch is more prone to break than one that's not used much, so be sure to replace the lock with a new, secure version when you spot any indications of wear or damage.

Once you've checked the lock and determined which type of replacement you'll need now is the time to start working on the actual repair patio doors. The spindle and handle should be removed from the doorway to the patio. Install the new handle. Start by putting in the handle in the interior, aligning it with the spindle, and then securing it with the two screws or bolts that secure it. Install the exterior handle following the interior handle. Once you have completed these steps check the handles to make sure they can be shut and open easily and that the latch works correctly with the strikeplate.

Check the door's Strike

The strike plate and door latch are two parts that work together in order to secure the door. An incorrectly aligned strike plate and door latches can cause the latch to not latch the door in a proper manner. Fortunately, this problem is often easy to fix.

Examine the holes that receive the strike plate to make sure they are free of obstructions such as dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place and allow it to move horizontally, but not separating it from the frame of the door. Then, you can adjust the strike plate to ensure that its holes for receiving are aligned with the latch hooks on the door latch. After the strike plate has been adjusted, tighten the screws and test the door to determine whether it locks smoothly after the new adjustment.

Door strike plates can be a bit difficult to locate for homeowners with sliding patio door repair company doors, but they're essential to lock tilt and slide patio door repairs near me unlock your door. The metal plates are situated on the top and bottom jambs of your door, which are where they help support the latch. The door latch slides onto the strike plate and forms a seal. If the strike plate is damaged, rusted, or not properly installed, it could prevent the latch from locking the door securely.

One common reason for the patio door lock to not close or not close is a misalignment between the latch and strike plate. This can be confirmed using the "lipstick" test. Rub some lipstick along the edge of the deadbolt, then cover it with masking tape. The lipstick will leave the mark when you close the door. This will show you exactly where the latch connects to the strike plate. If the mark is too high or low, you can adjust the strike plate.

Sliding patio door locks help keep your home safe from intruders, and if they're not working properly, you need to solve the issue fast. If you follow these steps, you can fix the lock on your patio door and regain its functionality in a matter of minutes.