• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

If you have the grounded sort, you must buy a receptacle that has a ground terminal screw and slots for 3-prong grounded plugs. The prong carries the security floor to the steel body of any equipment that has a three-wire plug and cord. However, the neatest thing you can do to ensure a protected electrical system is to make sure the entire system is grounded and the ground circuit is electrically continuous, without any breaks. An appliance"s metallic frame can pose a safety hazard to you and your loved ones. If a power cord"s insulation wears away simply at the purpose where the cord enters the steel frame, contact between the steel present conductor and the metal body might make the entire equipment alive with electricity. Everyone in the family ought to know where and the best way to throw the grasp swap that cuts off all electrical current. Touching a charged metal frame of the appliance whereas simultaneously touching a water faucet or a radiator will make the current surge by way of you.

If the circuit holds, it"s attainable something you disconnected is defective. Check for brief circuits or other problems. If there"s no evidence of electrical fault within the fixtures, the problem could also be a lot present draw for the circuit to handle. There are two attainable explanations. Go back alongside the road, inspect each merchandise for potential fault, and plug every one back in. First, pull all the cartridge fuses and unscrew all the plug fuses within the panel. If the principle entrance is wired with fuses, pull the fuse block out and slip the fuses free. If your system operates with fuses, remove the fuse for the circuit you're working on and slip it into your pocket or toolbox. Or, if you have a circuit breaker essential disconnect, verify to see whether or not it has tripped to the OFF position. If your house's electrical system uses circuit breakers, journey the appropriate circuit breaker to its OFF place. Stand on a dry board or wooden platform when working with a fuse field or circuit breaker box.

In case you go away it close by, somebody may put the fuse back in while you're engaged on the circuit. Always assume an electrical receptacle or apparatus is energized till you prove otherwise with a circuit tester or by pulling a fuse or tripping the disconnect plug. It seems like a fancy three-pronged plug and contains three neon bulb indicators. There are only two slots for each plug in ungrounded receptacles. Try your receptacles with a small cheap tester called a polarity checker, designed for this goal. For correct operation and security, make sure all receptacles on every circuit are installed with the individual conductors going to the right terminals so there aren't any polarity reversals alongside the road. The lights will let you know if the polarity is appropriate and, if not, which strains are reversed. A alternative receptacle should match the one you might be removing. Step 2: Take off plate that covers receptacle by removing center screw with screwdriver. Ensure to loop line wires in clockwise course beneath heads of terminal screws so screw heads will pull wire loops tighter. Loosen terminal screws on receptacle and remove line wires.

Step 3: Remove two screws holding receptacle in electrical box. Step 5: Carefully fold wires into space in electrical field behind receptacle, then push receptacle into box. The first step needs to be taken even before a circuit trips. Step 4: Connect wires to new electrical receptacle with white wire under silver-coloration screw and black wire beneath dark-shade screw. In case you uncover a green wire or a naked wire in field, fasten wire underneath screw that has dab of inexperienced shade on it, then fasten it to field with grounding screw or clip. When you have the type that accepts plugs with two blades and one prong, your system should have three wires, certainly one of which is a grounding wire. Either two-prong or three-prong plugs will be plugged into these receptacles, however only the three-prong sort will carry the equipment grounding line to the electrical tools. Carefully pull receptacle out of field so far as connected line wires allow. At that point, the old electrical receptacle should be changed. Replace the outdated cord with a new one which has good insulation. Remember to examine, maintain, and make repairs wherever wires enter a metallic pipe (conduit), where the cord enters a lamp or lamp socket, and where in-wall cable enters an electrical field.