• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

The first line of defense is your door lock. It will prevent unauthorized access into your home. Locks might require replacement upvc door locking mechanism due to signs of wear and tear or other circumstances such as moving into a new house or a burglary.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will allow you to buy the lock that is right for you.

Deadbolt

If you want to ensure your door is secure from burglars, it's a good idea to install deadbolts. The bolt extends into the strike plate that is on the doorframe when it is locked, making it more difficult for burglars to break in through the door. A single cylinder deadbolt can be activated using an exterior key on the side and a thumb turn device on the inside. A deadbolt will only work only if it's correctly installed, though.

It is first necessary to determine whether the door already has a hole that is suitable for a deadbolt, or if you'll need to drill it. With the template included with your lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Then, use the tape measure to determine how high the deadbolt needs to be. Mark this high point on the door's edge and use the speedsquare to draw a straightline across the mark that you made to mark the bolt hole.

Then, using an electric drill, bore out the hole until it reaches the opposite side of the door. This could take a bit of time. Sand the hole and the door edge to make it smooth. It's also recommended to paint or stain the door at this point.

Once the door is ready remove any screws visible on the deadbolt. This will reveal the front and rear assembly of the deadbolt and its bolt inside. Then unscrew the old bolt and replace it with a new one to match the door hardware. You'll need to remove the bolt from the setplate. After that, you'll have to chisel the door frame to accommodate the strike plate.

If your strike plate is not in alignment It could be due to the previous installer didn't mortise it properly or that an installation of a weatherstripping altered the strike's location. You will need to re-mortise your strike plate and possibly even the deadbolt itself to fix the issue. Close and lock the deadbolt when you have completed this step. Make sure that the bolt is extending into the strike plate and then test the key to make sure it is able to open and close smoothly.

Knob

When a door knob is worn out it could make your business or home less secure. It may make it difficult to open or close the door, so it's a good idea to Replace door lock it. replacing lock on upvc door a knob is a relatively simple DIY project that shouldn't take more than 30 minutes to complete. You can use a screwdriver and pliers to get rid of the knob or handle Be careful not to harm any other parts on the door.

Spray WD-40 or another dry lubricant on the mechanism of your door knob prior to you begin. This will assist the new lock slide smoothly as you turn it. It's essential to select the best knob and handle that is compatible with your current doors to ensure proper operation. If you don't have a doorknob that is compatible, you will need to buy a replacement door lock.

To begin the replacement process, examine the old knob or handle to determine what screws are holding it in place. If there aren't any screws to hold it in place, you can use a screwdriver to wedge the cover plate between the hidden screws plate.

After taking the knob off examine it for indications of damage and rust. You'll need to clean it off if there are any marks or dents, but you shouldn't have to do anything major If the knob is in good shape.

Install the new knob. First, examine the new knobs to ensure that you're choosing the right one for your door. You'll want to pick one with an extended rod that's designed to lock into the rod mechanism on the second knob. After you've placed the new knob into the hole and then put it in the latch.

Thread the latch plate screws downwards and test the spring by pressing down repeatedly. The latch should pop up each time. Install the second knob and secure it to the rod mechanism of the first knob. Then, thread the other long screws from the knob's interior through the hole for the cylinder on the doorknob on the outside and secure it.

Latch

A latch is a piece metal that extends into the door jamb to keep it closed. It is operated by a knob or handle on the inside of the door or a thumb turn on the exterior side of the door. A deadbolt is a device used to secure a latch and prevent burglars from piercing the glass of the door. It also offers protection from the accidental or deliberate closing of the patio door lock replacement by pets or children. The latch can be fitted with a single cylinder deadbolt or double cylinder deadbolts based on the level of security you prefer.

Installing a latch involves the same steps as installing a deadbolt, but there are a few differences. First, determine the setback of the doorjamb by using a tape measure to be sure that the new lock will fit. The setback is the distance from the edge of the doorjamb to the center of the hole to accommodate the latch faceplate. Standard setbacks are 2 3/8 to 2. 3/4 inches. If your setback is larger it is possible to purchase a latch that is longer from a locksmith or hardware store.

Then, make a hole for the latch plate in the edge of the doorjamb. Utilize a chisel to chisel the latch mortise. Make sure that the depth is enough for the faceplate to be flush with the doorjamb. Place the strikeplate on the floor to ensure it's placed correctly.

If the strike is positioned too high, the door could be kicked in or pressure put on it with a crowbar or tire iron. This could also cause cracks in the doorjamb. To correct this, the strike can be lowered by drilling another hole into the doorjamb and cutting out the core of the previous hole.

The final step is to mount the new strike plate which is done by screwing it in place over the screw holes that are already in place. Then, use wood putty to cover the screw holes that were previously used and the bolt hole that is not used. After the putty has dried you can sand it down to give it a professional results.

Strike

The metal piece that engages the latch and deadbolt when the door is shut is an electric strike. It is a vital component of a lock's overall security, since it keeps the door shut and also provides additional resistance to force or kicks applied to the door. If a door is fitted with an electronic strike, it can be opened by using an entry key and a control unit that regulates its electrical impulses.

In the past, installing an electronic strike was as simple as cutting off a part of a doorjamb to release the latchbolt of a cylindrical lock from the pocket that is inside the strike. This modification is not just ugly however, it also exposes the mechanism for the latchbolt and the keeper to intruders.

Recently, several electric strike manufacturers have developed a new type of electric strike called the "No Cut" strike that doesn't require cutouts in the doorjamb to operate. They use a specific design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike has an internal ramp that raises the latchbolt and keeper whenever it receives an electrical impulse from a controller or reader. The latchbolt and keeper are pushed on the ramp thanks to the retraction. When the door is shut, the deadbolt remains in place and the latchbolt retracts in the keeper.

Installing an electric strike can be an easy process, particularly when you are replacing patio door lock a strike on an existing door. However, if you're upgrading to an electric strike in an access control system, you'll have to ensure that your new system is compatible with the type of lock you've installed. Also, you must make sure that the strike is connected to your access-control system and set up to operate in a fail-safe way.

Upgrade your strike plates to heavy duty strike plates to prevent unauthorised entry. These plates use up to six screws of three inches instead of the usual two screws of three-fourths inch. These longer screws make breaking the frame to reach the piece that turns the thumb on a single deadbolt for a cylinder more difficult.