• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Door locks are the first protection against unauthorised access to your home. The locks may need to be replaced because of signs of wear and tear or other events like moving into a new home or a burglary.

To begin, you must determine the size of your cylinder using the distance between the adjustment screw and the middle of the knob lock cylinder. This measurement will enable you to purchase the correct-sized lock.

Deadbolt

If you're looking to ensure that your door is safe from criminals, it's a great idea to install a deadbolt. When the bolt is extended into the strike plate of the doorframe it makes it much more difficult for an intruder to get through the door. A single cylinder deadbolt is activated using an exterior key on the side and a thumb turn piece on the interior. A deadbolt will only work only if it's correctly installed, though.

First, you must determine if the door has an existing hole for a deadbolt, or if you need to drill it. Mark the location of the hole to install the deadbolt on the surface of the door using the template that came with the lock installation set. Use a tape measure to determine the height of the deadbolt. Then, mark this height on the side of the door. Use the speed square to draw an even line across the mark you made for the bolt hole.

Then by using an electric drill, bore out the hole until it is on the opposite side of the door. This could take a while. Sand the hole and the edge of the door to make it smooth. At this stage, it's a great idea cost to replace upvc door lock mechanism near me paint or stain your door.

Once the door is ready take off any screws that are visible on the existing deadbolt. This will reveal both the front and rear assembly of the deadbolt, as well as its internal bolt. Then, remove the bolt and Replace Door Lock it by the new bolt to match your door hardware. You'll need to remove the bolt from a setplate. After that, you'll have to chisel the area on the door frame to accommodate the strike plate.

If your strike plate is out of alignment, it could be because the previous installer failed to mortise it correctly or a weatherstripping changed the strike's position. It is necessary to re-mortise your strike plate and possibly even the deadbolt to correct this problem. Once this is completed check the deadbolt by closing and replacement locking mechanism for upvc doors it. Make sure the bolt is extending into the strike plate and then test the key to make sure it is able to open and close smoothly.

Knob

When a door knob is damaged it could make your home or business less secure. It may also make it harder to open or close the door, so it's an ideal idea to replace the knob. Replacing the knob is an simple DIY project that shouldn't take more than 30 minutes to complete. You can use a screwdriver as well as pliers to get rid of the knob or handle However, be careful not to scratch any of the other components on the door.

Spray WD-40, or another dry lubricant, on the mechanism of your door knob before you begin. This will let the new lock to slide smoothly as you turn it. To ensure that it operates properly it is important to select the knob and handle that match the doors you already have. If you don't have a doorknob that matches and handle, you'll need to purchase a new one.

Before you begin the replacement locks for patio doors process, examine the old knob to determine which screws are keeping it in place. If there aren't any screws to hold it in place, you can use a screwdriver to secure the cover plate between the screws plate that is hidden.

After you've removed your old knob, examine it for any signs of damage or rust. You'll have to scrub it off if you notice any scratches or dents however, you shouldn't need to do anything major when the knob is in good condition.

It's time to install the new knob. You must first study the two knobs in order to make sure that you've selected the right one for the door. You'll want to pick one with an extending rod designed to interlock with the rod mechanism on the second knob. Once you've positioned the new knob in the door's hole and then carefully place it in the latch.

Test the spring by pressing down on it repeatedly. The latch should then spring back up every time. Install the second knob and secure it to the rod mechanism of the first knob. Thread the long screws of the interior doorknob into the holes for cylinders on the exterior knob and secure it in place.

Latch

A latch is a piece metal that extends through the door jamb to keep it shut. It is operated by a handle or knob on the interior side of the door or by a thumb turn on the outside side of the door. The latch can be secured using a deadbolt to keep thieves from breaking through the door's glass. It also provides protection from the accidental or deliberate closing of the door by children or pets. A latch can be installed with single cylinder deadbolts or a double cylinder deadbolt, depending on the security level you prefer.

Installing a latch requires the same steps like installing a deadbolt however, there are a few variations. To make sure that the new lock will fit first, you must measure the setback on the doorjamb with an instrument such as a tape measure. The setback is the distance from the edge of the doorjamb to the center of the hole that will be used for the faceplate of the latch. Standard setbacks are 2 3/8 to 2. 3/4 inches. If you have a larger setback, you may need to purchase a larger latch at a hardware store or locksmith.

The next step is to drill an edge bore hole in the doorjamb to accommodate the latch plate. Use a chisel to chisel out the mortise of the latch and ensure it's deep enough to allow the faceplate of the new latch to be flush with the doorjamb. Place the strikeplate on the floor to ensure it is positioned properly.

If the strike is too high, you can push the door back or apply pressure with the tire iron or crowbar. This can cause the doorjamb's to crack. This can be repaired by drilling a new hole through the doorjamb, then chiseling the core out of the previous one.

The final step is to mount the new strike plate which can be accomplished by screwing it in place over the existing screw holes. Use wood putty then to fill in any existing bolt holes or screw holes that aren't being used. Once the putty has dried then sand it to an even finish.

Strike

The piece of metal that is inserted between the deadbolt and latch when the door is closed is an electric strike. It is a crucial component of the overall security of a lock because it helps keep the door shut and also provides additional resistance to force or kicks applied to the door. If a door has been equipped with an electric strike, it can only be opened by a key or the control unit that governs the electrical impulses.

In the past, installing an electronic strike was as simple as cutting a portion of a doorjamb to let the latchbolt of a cylindrical lock from the pocket inside the strike. This change can be a drawback when it comes to the appearance of openings and also exposes the latchbolt and keeper mechanism to unintentional users.

Recently, several electric strikes manufacturers have developed a "No Cut" type of strike that doesn't require a cutout for operation. These strikes use a special design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjamb's faceplate.

The strike has an internal ramp which lifts the latchbolt as well as the keeper when it receives a signal from an individual reader. The latchbolt and keeper are pushed up the ramp due to retract. When the door is closed, the deadbolt remains retracted, and the latchbolt retracts in the keeper.

Installing an electronic strike is a simple procedure, particularly if you're replacing an existing strike. However, if you're upgrading to an electric strike for an access control system, you'll be required to ensure that the new system is compatible with the kind of lock you've chosen to install. You will also need to ensure that the strike is properly wired to your access control system and is designed to operate in a fail-safe manner.

One way to safeguard against unauthorized access is cost to replace upvc door lock mechanism near me upgrade the strike on your doors to a high-quality strike plate. These plates use up to six screws of three inches instead of two screws of three-fourths of an inch. These screws are longer and make breaking the frame to reach the piece that turns the thumb on a single cylinder deadbolt more difficult.